Do you have a Dewalt reciprocating saw that needs to be cleaned?
I do, and I know how frustrating it can be when the saw isnt performing at its best. I will show you how to clean your Dewalt reciprocating see in just a few moments so it runs like new again.
Your saw will work faster and be more reliable if it is properly maintained. Plus, youll extend the life of your saw by taking care of it regularly. Follow these simple steps and youll be good to go!
How To Clean The Dewalt Reciprocating See
Here are some steps to clean you saw:
Cleaning The Blade:
The most important aspect of cleaning a Dewalt reciprocating see is the blade. If youve ever gotten anything stuck in the teeth of your reciprocating saw, then you know that its necessary to clean them thoroughly after each use. You can do this by hand or with an automatic blade cleaner (which has rotating brushes). Be sure to clean the blade thoroughly with a soft cloth.
What Do You Think About The Other Parts Of Your Dewalt Reciprocating Saws?
After you clean the blade, you can use a small amount of light machine oil or lubricating oil to remove any built-up grime on the outside of your tool. Paint thinner can be used to remove stubborn grease if the blade has become particularly filthy. Finally, if there are any loose parts inside the housing, tighten them by hand so they dont fall off during operation.
Motor Cleaning:
You shouldnt have to clean the motor of your Dewalt reciprocating saw on a daily basis. If the motor is heating up or smelling funny after prolonged use, it’s time to deep clean. Begin by disconnecting the power source and removing the blade guard. After that, spray compressed air into all intakes and exhausts on the blade housing until they are free of debris.
Use paint thinner to remove grime using a soft cloth. You can also brush with light oil if necessary. To ensure thorough cleaning, you can take out each attachment of the Dewalt reciprocatingsaw (i.e. blades, guards), and wash them individually with warm water, soap, a sponge, and some oil.
How Do You Clean The Housing Of A Dewalt Reciprocatingsaw?
The housing’s exterior needs to be cleaned after you have cleaned the blade of your Dewalt reciprocatingsaw. Use paint thinner to remove stubborn dirt and grime. You can also use paint thinner mixed with light machine oil to clean up older models that use oil instead of grease.
If there are any bolts or screws loose inside the housing, tighten them by hand before using your Dewalt reciprocating saw again.
Why Does My Dewalt Reciprocating Saw Smell Bad?
If the smelly problem persists after cleaning your Dewalt reciprocatingsaw’s motor and other parts, there may be oil in the motor housing or motor area. If you notice any leaking fluids, then be sure to clean them up before using your Dewalt reciprocating saw again.
Does That Pretty Much Cover It?
Yes! These steps will make your Dewalt reciprocating see look and smell like new. This will allow you to get back to work quickly. Our tools are an important part of our livelihood, so learning how to clean a Dewalt reciprocating saw is one of the most valuable skills for homeowners and contractors alike.
I Found Useful Tips About My Dewalt Reciprocal.
Its okay to use WD 40 on electric power tools but it shouldnt be used on the internal parts of the motor.
The best oil for your saw is light machine oil, which can be found at any hardware store.
If you are using a reciprocating saw without a blade guard, make sure to wear safety goggles or glasses at all times!
When the reciprocating saw is running, you should not place your hand in front of it. Always keep your hands behind the tool and away from its moving parts.
How Do You Lubricate The Moving Parts On A Dewalt Reciprocatingsaw?
There are several ways to keep the moving parts of your reciprocating saws well-lubricated. Light machine oil can be purchased at any hardware store. Another way is to spray some WD 40 on the housing of your Dewalt recprocating saw then wipe it down with a soft cloth (make sure not to get it in the motor area). You can also try paint thinner or light machine oil if you find that your blade is clogging up.
Safety Precautions
- Always keep your hands on the blade.
- It is not a good idea to point it at anyone, even yourself.
- Always wear safety glasses or goggles when using a reciprocating saw.
How Can I Sharpen My Dewalt Saw’s Teeth?
If the blade is not becoming dull or you don’t see any indications of it, you can use a file to sharpen it. You should use a steady, up-and-down motion while moving along the length of your Dewalt reciprocalsaws blade.
What Oil Is Best For My DeWALT Reciprocatingsaw?
The best oil to use for your DeWALT reciprocal saws motor is light machine oil, which can be found at any hardware store. However, if your reciprocating saw uses separate oil for its motor instead of grease, then you can use coating or sewing machine oil.
Conclusion
Dewalt reciprocating saws are a popular choice for DIYers and professionals alike. Theyre durable, efficient, and can handle a wide variety of cutting tasks. However, like any other piece of equipment, they need to be cleaned properly in order to maintain their performance and lifespan. In this article, Ive outlined the steps you need to take to clean your Dewalt reciprocating saw safely and effectively.
